AquaPRO PRO1100e TCE Provozní pokyny stáhnout pdf (Strana 7)

ambient temperature is below 50°F (38°F

for all other units with a Digital Control

Board), which is too low for the heater to

operate, or the unit is low on refrigerant.

Once the outside temperature has risen

above 60ºF, and the LP code remains, call

the factory for repair.

PSd: This code means there is a pool sensor

defect. Please call to arrange service for

the heat pump.

DSd: This code means there is a defrost

sensor defect. Please call to arrange

service for the heat pump.

LP3: This is like the “LP” described

above, however the unit has shut

down because this fault has happened

3 times within a 24 hour time period.

If the ambient temperature is below

50°F (38°F for all other units with a

digital control board), the problem will

most likely persist until the ambient air

temperature rises above 50°F. Pressing

any of the buttons on the front control

panel will restore the unit to its normal

operating mode. If the ambient air

temperature is not the issue and the

heat pump continues to display “LP” or

“LP3”, please call to arrange service for

the heat pump.

HP3: This is like the “HP” described

above, however the unit has shut down

because this fault has happened 3 times

within a 24 hour time period. Please

check your pool’s plumbing, valves and

pump / ﬁlter system for blockages or

ﬂow restrictions, as this is most likely

the cause for the fault. Pressing any

of the buttons on the front control

panel will restore the unit to its normal

operating mode. If your pump and

ﬁlter system is working normally and

there are no ﬂow restrictions and the

heat pump continues to display “HP”

or “HP3”, please call to arrange service

for the heat pump. Please note, we will

not be responsible for non-warranted

service calls.

FS: This code has the following

sequence:

• When rst displayed, the unit has

started the defrost cycle and will

reverse operation for 2 minutes. If

unit is at acceptable temperature

after the defrost cycle, it will go back

into heating mode.

• If coolant temperature is still too

low after the initial 2 minute

defrost cycle, unit will shut off the

compressor and run only the fan for

60 minutes. If unit is at acceptable

temperature after the 60 minutes, it

will go back into heating mode.

• If coolant has not reached the desired

temperature after the 60 minutes,

fan only mode, unit will shut down

and display “FS”.

• Unit will resume normal operation

after ambient temperature reaches

acceptable operating temperature.

MODELS: 1300h/c FS: If in “cooling-

mode”, this may indicate that there is not

enough water ﬂow.

COL: This code reminds you that the

unit is running in the cooling mode.

LP: If in “cooling mode”, this code may

indicate that there is not enough water

ﬂow

HP: If in “cooling mode”, this code may

indicate that an external coil is blocked

or that there is recirculated air.

HOT: This means the pool temperature has

increased by 2° while the unit is operating

in the “COL” mode. This is only a warning

that the unit is having difﬁculty cooling

the pool to the desired temperature. The

“HOT” message will remain until either

the pool drops to the desired temperature

or the set “COL” temperature is raised

above the pool’s current temperature.

MODELS: 1100E Series, 1300 Series

AND 1300H/C Series

FL3: This code means that water ﬂow

was lost. Check the system for ﬂow

obstructions.

Unit is not running (All Models):

• Check the power light. Check to see

if the breaker is set.

• Make sure the ltration system is on

• Make sure the thermostat is higher

than the pool water temperature

• Make sure the lter is clean and is

allowing enough water to ﬂow

• Make sure the outside ambient

temperature is higher than 50ºF (38°F

for all other units with a Digital Control

Board)

• Make sure the 5-minute time delay

has passed

• Make sure the 208/230 VAC

transformer is wired to match in

coming power levels.

FOR TCE UNITS

• Make sure time setting, in “FIL”

mode, is not set to “OFF”.

Unit is running but not heating:

• Check the air coming out of

the top of the unit. It should be

approximately 8ºF to 15ºF lower

than the surrounding ambient air

temperature. If not, call for service.

Unit is running but not cooling:

• After 5 minutes, Check the air coming

out of the top of the unit. It should

be approximately 8ºF to 15ºF higher

than the surrounding ambient air

temperature. If not, call for service

Unit will not cool:

FOR h/c UNITS:

• Make sure P-S is set to “POL” mode

as unit will not cool in “SPA” mode.

Unit runs continuously:

It may be running continuously

because it cannot reach the desired

temperature.

• Lower the temperature setting below

the pool water temperature. Unit

should turn off. If the unit is still

running, call for service.

• A pool blanket may be required to

help reach this temperature. Also, the

ﬁlter pump may need to run longer

for the heater to reach the desired

temperature.

FOR TCE UNITS

• Make sure the setting is not set to

“ON” position in the “FIL” mode.

Unit is cycling:

• Check the lters for proper water

ﬂow

• Check the evaporator coil for severe

frost

• Unit could be low on refrigerant.

At this point, call for service and

turn off the power to the heater to

keep the cycling from damaging the

compressor.

Troubleshooting

Guide

(continued)

1 2 3 4 5 6 7 8 9 10

Komentáře k této Příručce

Žádné komentáře

AquaPRO PRO1100e TCE Provozní pokyny Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Nadzemní příslušenství bazénu AquaPRO PRO1100e TCE